Go to Top

Line Cards

 

Power Distribution
Complete electrical distribution system design – at any voltage level
MCC and switchgear specification
Low and medium motor starting and control
Generators and UPS backup systems
VFD specification and configuration
Power transformer specification and protection
System grounding and equipment bonding
Lighting systems
Heat trace
Resistive grounded systems

 

Control Systems
Single and multiple PLC system design & installation
PLC programming and implementation
Graphical users interfaces- both PC based and stand-alone
Instrumentation and process design & installation
Fire and gas detection design & installation
Complete automation system networking & installation
SCADA systems
Wireless radio links
Fiber optic links

 

Power Studies and System Evaluations
Load flow
Voltage drop
Single and multistage power factor correction
Protective device evaluation and coordination
Motor starting
Voltage sag
Transient disturbances
Power management and load shedding

 

Instrument Installation and Calibration
Full range of instrument manufacturers and applications
On site gas analysis
On site calibration services
On site EFM calibration
Quarterly EFM certification

 

Engines
Visual Inspection on and around equipment
Cylinder compression testing
Power head valve lash adjustment
Oil samples taken as needed
Oil changes and oil filter replacement
Air and fuel filter replacement as needed
Lubricate all points as needed
Panel inspection and repair
Safety shutdown system check
Cooling system inspection and repair
Accessory repair or replacement
Complete overhauls as needed
Cosmetic upgrades

 

Compressors
Quarterly, semi-annual, and annual inspections
Frame overhauls in the field and shop
Checking, manufacturing, torque specifications on all frame bolts
Checking and performing cylinder preload checks
Performing cylinder pull down checks
Compressor frame soft foot check
Crankshaft web deflection check
Crosshead clearance checks
Valve replacement
Experienced troubleshooting methods
Any leak repair as needed
Perform coupling alignments
Panel inspection and repair
Safety shutdown system and repair
Cosmetic upgrades

 

Pumps
Bearing replacement
Seals repair and replacement (mechanical seals and oil seals)
Pump replacement/ new install
Pump overhauls in-house or field
Coupling alignment and pump set-up
Panel inspection and repair
Safety shutdown system check and repair

 

Panel Shop
UL and NEMA listed industrial control panels
Class I Div I & Class I Div II panels
UL 508/508A listing
UL 698/698A listing

 

Gas Analysis & Calibration

We provide mobile gas analysis for any and all industrial/oil & gas applications. We are capable of handling all your gas analysis and calibration requirements. Gas analysis equipment can be traced back to the NIST standard, and all calibration equipment is certified annually. We also have the ability to give detailed electronic reports and/or running data acquisition. We are capable of monitoring all data required from any pipeline or well site for trending needs or statistical process control.

 

On-Site Gas Analysis-
Analysis of the following types of gases:
CO2, Nitrogen, Methane, Ethane, Propane, I Butane, N Butane, I pentane, N Pentane,
C6(hexanes), C7(heptanes), C8 (octanes), C9+ (nonanes, dectanes)

 

Calibration of Electronic Measurement
Including but not limited to the calibration of:
Fisher ROC
Control Microsystems
Rosemount
ABB Total Flow
Endress Hauser
Rockwell Automation
Siemens
Foxboro

 

Calibration of Dry Flow Measurement
Including but not limited to:
Barton
Reynolds
American
Foxboro

 

Water dew point analysis (onsite)
Ability to measure dew point from 1lbs to 100lbs
On-site spot H2S analysis
Trace oxygen analysis 0-10%
Orifice plate inspections
On-Site calibration of Hart devices
Start-up and turnaround assistance of pneumatic and electrical equipment

 

Calibration of Gas and Flame Detectors
Including, but not limited to:
Detector Electronics – Detronics
General monitors
Spectrum

 

Roustabout Services: 

 

Specialized Automation Services, LLC is a locally owned, fully licensed and insured contractor on the Western Slope.  SAS is honest, dependable and dedicated to our clients needs with local support and staff, competitive pricing and 24/7 service available.  SAS has a zero tolerance drug and alcohol policy, and is fully dedicated to our “Safety First” program.

  • Mechanical construction
  • 24/7 service and call outs
  • Civil construction
  • Maintenance work
  • Excavation and backfill
  • Contract pumping
  • Roustabout service
  • Well maintenance
  • General cleanup
  • Cathodic protection
  • Welding
  • Re-claims & storm H2O management
  • Hot taps
  • Pipefitting
  • Fence work
  • Rig support
  • Re-seeding
  • Under rig/pit liners
  • Painting
  • Liner repairs
  • Bird netting, maintenance & repair
  • Snow removal
  • Cattle guards
  • Power washing
  • Dust control
  • Hot shot service

 

Equipment Available:

  • Assorted sized trucks
  • Trailers
  • Backhoes
  • Track hoes
  • Excavators
  • Mini excavators
  • Skid loaders
  • Trenchers
  • Trash trucks
  • Forklifts